What is stop error 24 on KitchenAid dishwasher? The stop error 24 on KitchenAid dishwasher is a diagnostic code indicating a fault with the motor drive.
The motor drive controls the dishwasher’s motor.
One of the most common causes of this error code is a fault with the motor drive.
- What is error code 24 in KitchenAid dishwasher? This error occurs due to issues with the computer’s hardware and operating system.
- Corrupted error logs are one of the most common causes of this error message.
- Corrupted DLLs can also trigger the Stop 24 error, so be sure to run a dedicated tool to repair them and restart your computer.
PC problems? Solve them in minutes.
Check dishwasher’s drain
- Unplug the dishwasher and check for blockage.
- Check if the filter is clogged.
- Clean the filter.
- Turn off the water before starting the cycle.
- If the drain is clogged, try running the dishwasher with a clogged filter.
Check water supply
- Check if the water supply is working properly.
- Consult the manual of your dishwasher for the drainage assembly.
- If the drain is clogged, remove the drain hose and wash it with hot water.
Check drain hose
- The drain hose or drain pump may have become clogged.
- Try running the dishwasher using an alternative drain hose.
- If even that fails, the drain pump may need replacement.
Check water filter
- Press the Start button, then type “services” in the search bar, then select Services.
- In Services, scroll down to Service Status and locate the one related to your water filter.
- Right-click on it, and select Restart.
PC problems? Solve them in minutes.
Is your computer running slow, crashing, or giving you the dreaded Blue Screen of Death? Well, don't worry - there's a solution! ASR Pro is the ultimate software for repairing Windows errors and optimizing your PC for maximum performance. With ASR Pro, you can fix a wide range of common issues in just a few clicks. The application will detect and resolve errors, protect you from data loss and hardware failure, and optimize your system for optimal performance. So don't suffer with a slow or crashed computer any longer - download ASR Pro today!

Reset the dishwasher
- Press the Start button, then type reset, and select Reset This PC.
- On the Reset This PC window, select the Troubleshoot option.
- Then, click the Reset this PC option.
- Follow the on-screen instructions to complete the process.
Reset the water supply
- Turn off the water supply to the dishwasher.
- Open the upper and lower hoses to the dishwasher.
- Press the Water Supply button.
- Check to see if the water has stopped draining from the dishwasher after the reset.
- If not, try resetting the water supply again.
- Reset the dishwasher
Press and release the Power button. - Press and release the Start button 3 times.
- Wait for 10 seconds and press the Power button once.
- Press and release the Start button to enter service mode.
Disconnect dishwasher
- Disconnect the dishwasher from the power source and disconnect the power cable from the outlet.
- Disconnect the water lines
- Disconnect the drain line
Disconnect the drain line (normally, the other end of the drain line is connected with your sink). - Disconnect the dishwasher drain hose
Disconnect the drain hose. - Remove the cover
- Remove the cover of the dishwasher.
- Remove the food debris
- Remove all the food debris from the dishwasher and clean it.
Change drain line filter
- The drain line filter can be easily replaced, and it’s usually located at the bottom of the dishwasher.
- To access the filter, you will need to remove the lower front panel of the dishwasher.
Disconnect the water supply
- Turn off the water valve supplying water to the dishwasher.
- Open the door of the dishwasher.
- Disconnect the water supply hose from the dishwasher.
- Disconnect the drain hose from the dishwasher.
- Remove the dishwasher from the wall.
- Clean the detergent dispenser using a warm, wet cloth.
- Disconnect the dishwasher drain hose from the dishwasher.
- Clean the drain hose using a wet cloth.
- Reconnect the dishwasher drain hose to the dishwasher.
- Reconnect the water supply hose to the dishwasher.
- Reconnect the dishwasher to the wall.
- Turn the water valve back on.
